Category: Audi

Audi engine ECUs and the VAG platform
Audi shares its engine electronics with the wider Volkswagen Group. The engine control units fitted to Audi models are, in the great majority of cases, the same Bosch and Siemens families used across VW, SEAT and Škoda, so the units we repair carry the well-known VAG references rather than Audi-only part numbers. On the petrol side that means Bosch Motronic and MED-series control units driving the FSI and TFSI direct-injection engines; on the diesel side it means Bosch EDC common-rail units and the Siemens Simos PPD injectors used on the earlier PD engines.
What matters when one of these units fails is that it is already coded and paired to your specific car. Rather than fitting a replacement and starting that relationship again, we repair the original module at component level — the fault is corrected on the circuit board and the unit goes back keeping every bit of coding and immobiliser data it left the factory with. The sections below set out the Audi/VAG control units we cover, the failures we see most often, and how the mail-in repair works. The individual part-number pages sit directly beneath this introduction. Audi and VAG control units in our library
Because Audi engine management is shared across the VAG range, our part-number library is organised by the ECU family rather than the badge on the car. The units we repair span the petrol and diesel generations you are most likely to be searching for:

Bosch EDC17 common-rail diesel control units for the TDI engines — the CP04, CP14, CP20 and U01 variants — including the widely fitted Bosch EDC17CP20 TDI diesel ECU.
Bosch MED17 direct-injection petrol units for FSI and TFSI engines, such as the Bosch MED17.5.20 petrol ECU.
Siemens/Continental Simos PPD1 pump-injector (Pumpe-Düse) diesel units in the 1.1, 1.2, 1.3 and 1.5 variants, including the Simos PPD1.3 PD diesel ECU.
Magneti Marelli 4-series petrol control units, such as the Magneti Marelli 4HV petrol ECU.
Earlier Motronic and Simos petrol control units from the preceding engine generations are covered too.

If the reference on your unit is not one you recognise here, our technical team will confirm whether we cover it rather than leave you to guess — each part-number page below carries the specific details for that unit. How Audi and VAG engine ECUs typically fail
Failures on these units tend to repeat in recognisable ways, and nearly all of them are correctable at component level rather than needing a whole new module. The patterns we handle most often are:

No communication — the ECU stops responding to a diagnostic scan altogether, which commonly traces to a failed communication transceiver or corrupted internal memory.
Damage from a jump-start — a voltage spike or a reversed-polarity connection while boosting a flat battery frequently takes out the unit’s power supply or an output stage. This is one of the most common reasons an Audi ECU arrives with us.
Limp mode and misfires — where the module has lost proper control of one or more injector or ignition outputs.
Crank but no start — the engine turns over yet never fires, often because the unit has lost stored data or its immobiliser link to the car.
Water ingress and corrosion — several VAG units sit low down or in the scuttle area, where damp reaches the board and corrodes tracks and solder joints over time.
Corrupted EEPROM or flash, failed injector drivers and relay-pack faults — internal component failures that a like-for-like replacement would swap out needlessly.
Is the fault the ECU, or something else?
Engine-ECU symptoms overlap heavily with wiring, sensor and battery problems, so it is worth knowing which signs point back at the control unit itself. The clearest indicators are an engine that cranks but never starts, a repeated and sudden drop into limp mode, misfiring that does not track to a single cylinder, warning lights that will not clear, or a unit that has stopped answering a scan tool. A fault that showed up immediately after a jump-start, a flat battery or work around the ECU connector points strongly at the module.
Because those symptoms have more than one possible cause, every unit that reaches us is logged, inspected and electrically tested before any conclusion is drawn. A module is never written off, or repaired, on assumption — the diagnosis comes first. Component protection: why we keep your original unit
VAG vehicles use component protection (Komponentenschutz), a security scheme that ties the engine ECU to the specific car it was installed in. This is exactly why replacing an Audi engine ECU is rarely a simple swap: a new or used unit has to be enrolled and adapted to the vehicle, and a used ECU pulled from another Audi brings its own protection data that has to be cleared and re-matched — specialist equipment and dealer or diagnostic time on top of the part itself, with no guarantee it takes cleanly.
Repairing the original unit sidesteps all of that. Because the fault is fixed on the board and your own module is retained, it goes back already enrolled to your car — no reprogramming, no component-protection re-adaptation, and no immobiliser re-coding when it is refitted. In practice it is a plug-and-play return: the unit fits and runs exactly as it did before the fault appeared, and you keep the original hardware Audi paired to the vehicle. Where a unit is genuinely beyond economical repair, we also hold exchange units for many VAG references. What the repair-and-return service involves
This is a mail-in service covering the whole of the UK, run without a walk-in counter by design. When your unit arrives it is logged, visually inspected and electrically tested, then taken through fault-specific diagnostics for its ECU family. We contact you with the outcome and an estimate before any chargeable work starts, so nothing proceeds without your authorisation. All component-level work is carried out in our own workshop by our own engineers, under a microscope with temperature-controlled rework equipment, using only genuine OEM-grade parts.
A repair is not signed off until it has passed final testing on the bench, and the work is protected by a 24-month warranty covering the specific fault we rectified. Tested before and after, original unit retained and still paired, and covered for two full years — that is what makes repair-and-return a dependable alternative to sourcing and adapting a replacement Audi ECU. Send your Audi ECU in for repair
Find your exact EDC17, MED17, Simos PPD1 or Magneti Marelli reference in the Audi part-number pages below, or let our engineers confirm coverage for your unit first. To begin, complete the Repair Form on our contact page for a diagnosis and quote. The full range of makes and modules we cover is on our What We Repair page.